The Radio Amateur - New- Hints And Kinks For

Strip the insulation off a length of stranded hookup wire (16–22 AWG). Unravel the braided shield or simply flatten the stranded core. Dip the bare copper in rosin flux (paste or liquid). Apply your soldering iron to the joint and touch this makeshift wick to the molten solder.

Tried-and-true tricks, fresh twists, and shop-tested solutions for the modern shack

Let’s face it: half the fun of amateur radio is the tinkering. We love solving the little problems—the RF in the shack, the cable mess behind the desk, the soldering iron that’s never hot when you need it. Here’s a fresh batch of hints and kinks to save you time, money, and frustration. The problem: You slip a ferrite bead over a coax cable, but it rattles around and slides right off the bend. Not effective.

Use vulcanizing silicone tape (often sold as "rescue tape" or "self-fusing silicone tape"). It’s about $8–10 per roll. Stretch it 100% as you wrap—it fuses to itself into a solid rubber sleeve. New- Hints and Kinks for the Radio Amateur

Loosen the element set screw. Slide the element until it touches the clamp. Tighten. Check SWR. Move clamp up or down by measured inches. No more lowering the mast 15 times. 6. Cleaning Potentiometers Without Deoxit (Field Hack) The problem: Scratchy volume or tone control on your vintage receiver, and you’re out of contact cleaner.

WD-40 leaves a residue that attracts dust. This alcohol+oil method flushes oxidation then leaves a clean, thin lubricant film. 7. The "No-Drill" Ground Bus for a Metal Desk The problem: Your station ground needs a common bus bar, but you don’t want to drill into your nice metal desk or filing cabinet.

Now get on the air—and keep the hints coming. Strip the insulation off a length of stranded

Remove the knob. Drip 2–3 drops of isopropyl alcohol (91% or higher) into the shaft opening. Rotate the pot back and forth fully 20–30 times. Let it dry 5 minutes. Then add one tiny drop of lightweight machine oil (sewing machine oil or even 3-in-1) to the same spot. Rotate again 10 times.

Use a second mat as a soldering iron rest when traveling. The iron tip won’t burn it, and it won’t slide off the table. A Final Word The best kink is the one you discover yourself. Keep a small notebook in your shack (or a digital note) and write down every “that worked well” or “that was stupid, don’t do it again.”

Tighten until it stops with light finger force, then use the screwdriver for no more than 10 degrees of additional rotation. 4. Cheap Coax Seal That Doesn’t Turn to Gum The problem: High-end coax sealing tape (Coax-Seal, etc.) works great, but it’s expensive and gets sticky-messy in heat. Apply your soldering iron to the joint and

This is for RF ground and equipment bonding , not for lightning or AC safety ground. Always keep your AC safety ground separate and intact. 8. Silicone Baking Mat = Portable Work Surface The problem: Tiny screws, washers, and springs roll off your bench and into the abyss (also known as the carpet).

73, and may your SWR be low and your soldering iron hot. Do you have a kink to share? Send it to your club newsletter or post it on QRZ—that’s how our tradition stays alive.

By WB2FAS (In the spirit of the original QST column)

Not always, but in a pinch, stranded 18-gauge wire soaked in flux outperforms no wick at all. Keep a 6" piece pre-fluxed in a tiny ziplock bag in your go-kit. 3. The "Eyeglass" SMA Wrench (Free & Perfect) The problem: SMA connectors need to be finger tight plus 1/8 turn . Overtighten, and you’ll snap the center pin or ruin the female receptacle (especially on cheap HTs or SDR dongles).